Page History

...

1. datatype awareness for hif_editimlist
2. need regcal and selfcal aggcont and cube images created and exported
3. Print pre/post beam info in per-solint table
4. skip mosaics implicitly
5. 3 digits past decimal for all values
6. Fix beam comparision ratios in per-solint stats
7. Change in nterms for high S/N sources for hif_makeimages

Post-SRDP Release (for Fall 2023)

...

•  Fix and suppress some warnings
  • "channel bandwidths ratio?" => see 

    Jira
    server DMS JIRA columnIds issuekey,summary,issuetype,created,updated,duedate,assignee,reporter,priority,status,resolution columns key,summary,type,created,updated,due,assignee,reporter,priority,status,resolution serverId eb2e750b-a83a-387e-8345-36eee8a98f01 key PIPE-1447

    is the result of averaging down to 15.625 MHz channels when there was pre-averaging
  • suppress representative target warnings
• main table:
  • solints to attempt - make the successful solints bolded
  • Mouseover text for success (define as: 'self-calibration solutions accepted for at least one solution interval')
  • Remove phasecenter, cellsize, and imsize from table
  • Remove the 'apply contline' and 'apply cont' columns
  • Add stop reason to table

...

Main page and results table:

• the page navigation with expanding sections is not used anywhere else and will be very unfamiliar - some of it is better than what is used elsewhere, but either way we should be more consistent
  • at the very least the buttons that expand alternative sections should have little "v" down arrow, or something indicating that they'll expand.
    or more consistent with the rest of the weblog would be to put all that on a subpage.
  • Some preference for this to open a new page
• Need 'View Other QA images'-type page page to show model, residual, mask, PB, and psf.
• the weird 3-dot, 3-line symbol at the start of the line is that takes you back up to the top - probably just ditch that for now or have explicit ('jump to top text')
• add mouseover text to Dist./Ratio that defines what this column is
• theoretical sensitivity should be plotted as filled, dark gray distribution rather than the horizontal bar, this will fix many issues with the current horizontal bar
• success "yes" looks like a clickable link but it isn't
• down the line it would be good to figure out how to display the large table of numbers graphically - its a lot of numbers to digest.  Or as a first step highlight table cells that indicate something interesting or potentially troubling is hapenning
• the table rendering is joining columns that probably shouldn't be joined, like "rms improvement" and "ratio of beam area" when they're both 1.0
• need to add residual and possibly model imagesRAL:
• 'Comparison' is unclear as to what it is calculating, and units are oddRAL: 'N.F.' → 'Near Field' and similar abbreviations made more clear
• RAL: why is 'flagged solutions by antenna' blank?
• abbreviation needs a mouse-over definition
• AAK: I would put stop reason higher

QA Plots subpages:

• need Need the "BACK" button like other subpages,
• again the The weird symbol with three dots and three lines doesn't seem to do anything except randomly port me somewhat upwards on the page, so probably should be removed for now.remove or make explicit what it does
• Passed "Yes" again is a link that doesn't do anything when clicked
• "Sol summary" needs better explanation and not use "Sol" probably; in particular what is doing the flagging - just gaincal?
• I'm not sure what the gain(phase) plots are intended to be used for - there doesn't seem to be a lot of information there - if one is supposed to note something, I think what to look for should be documented, or better yet a QA score calculated?
• 
  
  • sol. Summary - > selfcal solution interval summary
  • 'Sol.' in row names → Solutions
• Need 'View Other QA images'-type page page to show model, residual, mask, PB, and psf.
• The prior/post plots should show the same information per solint that is shown on the main page for consistencyThe QA note about "channel bandwidth ratio" doesn't have units and is a really huge number. It's not apparent what this means to me as a user.

• RAL: phase plots need to have consistent scale to be useful as thumbnails.
• RAL: 'Comparison' plot and stats missing here
• RAL: This is where I would expect to see a hif_makeimages style breakout of residuals, etc. that Amanda mentioned via email.

...